首页 > 产品中心 > Hempel 海虹老人 > 聚氨酯面漆 / 聚氨酯面漆
HEMPATHANE TOPCOAT 55910
BASE:55919
CURING AGENT:97050
Description:
HEMPATHANE TOPCOAT 55910 is a two-component polyurethane topcoat, cured with aliphatic isocyanate.
Recommended use:
As a VOC-compliant, high-build finishing coat for protection of structural steel in corrosive environment,especially for maintenance purposes. May be specified as a one coat “Direct To Metal” system in mild atmospheric environments.
Service temperature:
Maximum, dry exposure only: 120°C/248°F see REMARKS overleaf
Certificates/Approvals:
Complies with EU Directive 2004/42/EC: subcategory j.
Availability:
Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours:10000*/ White.
Finish: Semi-gloss
Volume solids, %: 65 ± 1
Theoretical spreading rate: 6.5 m2/l [260.7 sq.ft./US gallon] - 100 micron/4 mils
Flash point:31 °C [87.8 °F]
Specific gravity:1.5 kg/litre [12.5 lbs/US gallon]
Dry to touch: 5 approx. hour(s) 20°C/68°F
Fully cured: 7 day(s) 20°C/68°F
VOC content:325 g/l [2.7 lbs/US gallon]
*other shades according to assortment list.
APPLICATION DETAILS:
Version, mixed product:55910
Mixing ratio:BASE 55919: CURING AGENT 97050
7:1 by volume
Application method: Airless spray (see REMARKS overleaf) / Brush (see REMARKS overleaf)
Thinner (max.vol.):08080 (5%) / 08080 (5%)
Pot life:2 hour(s) 20°C/68°F
Nozzle orifice: 0.017 - 0.021 "
Nozzle pressure: 175 bar [2537.5 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S THINNER 08080 / 08880
Indicated film thickness, dry: 100 micron [4 mils] see REMARKS overleaf
Indicated film thickness, wet: 150 micron [6 mils]
Overcoat interval, min: According to specification.
Overcoat interval, max: According to specification.
Safety:
Handle with care. Before and during use, observe all safety labels on packaging and paint containers,consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION:
According to specification.
APPLICATION CONDITIONS:
Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
Minimum temperature for curing is: -10°C/14°F.
At the freezing point and below be aware of the risk of ice on the surface, which will hinder adhesion.
The film formation may be adversely affected by light rain, high humidity and/or condensation during application and the following interval after application: 24 hours , 20°C/68°F.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT:
According to specification.
SUBSEQUENT COAT:
None.
REMARKS:
Colours/Colour stability:
Colour stability for some shades may be effected by exposure to harsh chemical atmospheres. This does not affect the performance of the coating.
For certain colours (yellow, red, orange, green, etc.), extra coats may be necessary to obtain full opacity.
Weathering/service temperatures:
At service temperature above 100°C/212°F, slight discolouration may be expected. The product will become softer.
Application(s):
When specified as a one coat “Direct to Metal”-system follow “Good Painting Practise” and apply stripe coating before the spray application on areas difficult to cover properly by spray application.
CURING AGENT 97050 : is sensitive to moisture. Even small traces of water in the mixed paint will reduce the pot life and result in film defects.
Film thicknesses/thinning:
May be specified in another film thickness than indicated depending on purpose and area of use. This will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:minimum 50 micron/2 mils (diluted), minimum 75 micron/3 mils (undiluted), maximum 125 micron/5 mils.
Curing agent:
Open curing agent cans with caution as overpressure might exist.
Note:
HEMPATHANE TOPCOAT 55910 For professional use only.
ISSUED BY:
HEMPEL A/S 5591010000